Question

我正在尝试使用以下代码在arduino uno + ethernet shield上实现Modbus TCP。我在电脑上使用modbus slave模拟器来检查以下代码。但是，代码似乎不起作用。我已经下载了代码＆amp;来自http://myarduinoprojects.com/modbus.html的图书馆。如有必要，请建议我更正。还有另一个工作示例可用于arduino上的modbus tcp / ip。

感谢。

#include <SPI.h>
#include <Ethernet.h>
#include "MgsModbus.h"

MgsModbus Mb;
int inByte = 0; // incoming serial byte

// Ethernet settings (depending on MAC and Local network)
byte mac[] = {0x00, 0x1A, 0xB6, 0x02, 0xD1, 0x14 };
IPAddress ip(192, 168, 0, 35);



void setup()
{

  // serial setup
  Serial.begin(9600);
  Serial.println("Serial interface started");

  // initialize the ethernet device
  Ethernet.begin(mac, ip);   // start etehrnet interface
  Serial.println("Ethernet interface started"); 

  // print your local IP address:
  Serial.print("My IP address: ");
  for (byte thisByte = 0; thisByte < 4; thisByte++) {
    // print the value of each byte of the IP address:
    Serial.print(Ethernet.localIP()[thisByte], DEC);
    Serial.print("."); 
  }
  Serial.println();

  // slave address
  Mb.remSlaveIP = (192,168,0,1);

  // Fill MbData
//  Mb.SetBit(0,false);
  Mb.MbData[0] = 1;
  Mb.MbData[1] = 2;
  Mb.MbData[2] = 3;
  Mb.MbData[3] = 4;
  Mb.MbData[4] = 5;
  Mb.MbData[5] = 6;
  Mb.MbData[6] = 0;
  Mb.MbData[7] = 0;
  Mb.MbData[8] = 0;
  Mb.MbData[9] = 0;
  Mb.MbData[10] = 0;
  Mb.MbData[11] = 0;

  // print MbData
  for (int i=0;i<12;i++) {
    Serial.print("address: "); Serial.print(i); Serial.print("Data: "); Serial.println(Mb.MbData[i]);
  }
  // print menu
  Serial.println("0 - print the first 12 words of the MbData space");
  Serial.println("1 - FC 1 - read the first 5 coils from the slave and store them in the lower byte of MbData[1]");
  Serial.println("2 - FC 2 - read the first 5 discrete inputs from the slave and store them in the higer of the MbData[1]");
  Serial.println("3 - FC 3 - read the first 5 registers from the slave and store them in MbData[3..7");
  Serial.println("4 - FC 4 - read the first 5 input registers from the slave and store them in MbData[8..12]");
  Serial.println("5 - FC 5 - write coil 0 of the slave with the bit valeu of MbData[0.0]");
  Serial.println("6 - FC 6 - write register 0 of the slave with MbData[2]");
  Serial.println("7 - FC 15 - write 5 coils of the slave starting with coil 0 with GetBit(16..20");
  Serial.println("8 - Fc 16 - write 5 registers of the slave starting on register 0 with MbData[0..4]");

  Serial.println(Mb.remSlaveIP);
}

void loop()
{
  if (Serial.available() > 0) {
    // get incoming byte:
    inByte = Serial.read();
    if (inByte == '0') {                                          // print MbData
      for (int i=0;i<12;i++) {
        Serial.print("address: "); Serial.print(i); Serial.print("Data: "); Serial.println(Mb.MbData[i]);
      }
    }  
    if (inByte == '1') {Mb.Req(MB_FC_READ_COILS,               6,6,6);} // 1 // ref, count, pos
    if (inByte == '2') {Mb.Req(MB_FC_READ_DISCRETE_INPUT,      6,6,6);} // 2
    if (inByte == '3') {Mb.Req(MB_FC_READ_REGISTERS,           6,6,6);} // 3
    if (inByte == '4') {Mb.Req(MB_FC_READ_INPUT_REGISTER,      6,6,6);} // 4
    if (inByte == '5') {Mb.Req(MB_FC_WRITE_COIL,               0,0,0);} // 5 // count can be x
    if (inByte == '6') {Mb.Req(MB_FC_WRITE_REGISTER,           7,0,0);} // 6 // count can be x
    if (inByte == '7') {Mb.Req(MB_FC_WRITE_MULTIPLE_COILS,     0,6,0);} // 15
    if (inByte == '8') {Mb.Req(MB_FC_WRITE_MULTIPLE_REGISTERS, 0,6,0);} // 16
  }

  Mb.MbmRun();
//  Mb.MbsRun();
}

Answer 1

串行监视器工作正常。首先调试程序

时打印以下行

Serial interface started Ethernet interface started My IP address: 192.168.0.35. address: 0Data: 1 address: 1Data: 2 address: 2Data: 3 address: 3Data: 4 address: 4Data: 5 address: 5Data: 6 address: 6Data: 0 address: 7Data: 0 address: 8Data: 0 address: 9Data: 0 address: 10Data: 0 address: 11Data: 0 0 - print the first 12 words of the MbData space 1 - FC 1 - read the first 5 coils from the slave and store them in the lower byte of MbData[1] 2 - FC 2 - read the first 5 discrete inputs from the slave and store them in the higer of the MbData[1] 3 - FC 3 - read the first 5 registers from the slave and store them in MbData[3..7 4 - FC 4 - read the first 5 input registers from the slave and store them in MbData[8..12] 5 - FC 5 - write coil 0 of the slave with the bit valeu of MbData[0.0] 6 - FC 6 - write register 0 of the slave with MbData[2] 7 - FC 15 - write 5 coils of the slave starting with coil 0 with GetBit(16..20 8 - Fc 16 - write 5 registers of the slave starting on register 0 with MbData[0..4] 1.0.0.0

然而，似乎TCP通信不起作用，因为在此之后串行监视器上没有任何内容@ graham.reeds

Answer 2

我在办公室使用mgsmodbus作为我的modbuswork。我所拥有的是TI主板和Slave模拟器。但是我使用的是Wifi.h而不是ethernet.h。我能够完成所有操作。

您是否检查过以太网连接是否正确建立？

如果有，请尝试IBH Modbus从站模拟器。这很完美。您必须将设置更改为TCP并选择端口。有时您尝试的端口号可能是错误的。我使用默认的端口502。

另外，请确保.cpp代码中的从属IP也已更改。

Arduino上的Modbus TCP / IP

2 个答案: