有没有人有过使用Pontech Big-Easy Kard和quick420板移动简单的4引脚双极步进电机的经验？我只是试图采用所包含的Arduino控制步进电机的示例，并将它们移植到一起，以便它们能够在Pontech环境中正常运行。我试图转换的代码如下：
/*
Stepper Motor Control - one revolution
This program drives a unipolar or bipolar stepper motor.
The motor is attached to digital pins 8 - 11 of the Arduino.
The motor should revolve one revolution in one direction, then
one revolution in the other direction.
Created 11 Mar. 2007
Modified 30 Nov. 2009
by Tom Igoe
*/
#include <Stepper.h>
const int stepsPerRevolution = 200; // change this to fit the number of steps per revolution
// for your motor
// initialize the stepper library on pins 8 through 11:
Stepper myStepper(stepsPerRevolution, 8,9,10,11);
void setup() {
// set the speed at 60 rpm:
myStepper.setSpeed(60);
// initialize the serial port:
Serial.begin(9600);
}
void loop() {
// step one revolution in one direction:
Serial.println("clockwise");
myStepper.step(stepsPerRevolution);
delay(500);
// step one revolution in the other direction:
Serial.println("counterclockwise");
myStepper.step(-stepsPerRevolution);
delay(500);
}
我遇到的问题是我不知道如何正确转换定义引脚8,9,10和8的部分。 11是具有电机引线的那个。我知道它在.cpp文件中做到了。我在下面包含了Stepper.h和Stepper.cpp
/*
Stepper.h - - Stepper library for Wiring/Arduino - Version 0.4
Original library (0.1) by Tom Igoe.
Two-wire modifications (0.2) by Sebastian Gassner
Combination version (0.3) by Tom Igoe and David Mellis
Bug fix for four-wire (0.4) by Tom Igoe, bug fix from Noah Shibley
Drives a unipolar or bipolar stepper motor using 2 wires or 4 wires
When wiring multiple stepper motors to a microcontroller,
you quickly run out of output pins, with each motor requiring 4 connections.
By making use of the fact that at any time two of the four motor
coils are the inverse of the other two, the number of
control connections can be reduced from 4 to 2.
A slightly modified circuit around a Darlington transistor array or an L293 H-bridge
connects to only 2 microcontroler pins, inverts the signals received,
and delivers the 4 (2 plus 2 inverted ones) output signals required
for driving a stepper motor.
The sequence of control signals for 4 control wires is as follows:
Step C0 C1 C2 C3
1 1 0 1 0
2 0 1 1 0
3 0 1 0 1
4 1 0 0 1
The sequence of controls signals for 2 control wires is as follows
(columns C1 and C2 from above):
Step C0 C1
1 0 1
2 1 1
3 1 0
4 0 0
The circuits can be found at
http://www.arduino.cc/en/Tutorial/Stepper
*/
// ensure this library description is only included once
#ifndef Stepper_h
#define Stepper_h
// library interface description
class Stepper {
public:
// constructors:
Stepper(int number_of_steps, int motor_pin_1, int motor_pin_2);
Stepper(int number_of_steps, int motor_pin_1, int motor_pin_2, int motor_pin_3, int motor_pin_4);
// speed setter method:
void setSpeed(long whatSpeed);
// mover method:
void step(int number_of_steps);
int version(void);
private:
void stepMotor(int this_step);
int direction; // Direction of rotation
int speed; // Speed in RPMs
unsigned long step_delay; // delay between steps, in ms, based on speed
int number_of_steps; // total number of steps this motor can take
int pin_count; // whether you're driving the motor with 2 or 4 pins
int step_number; // which step the motor is on
// motor pin numbers:
int motor_pin_1;
int motor_pin_2;
int motor_pin_3;
int motor_pin_4;
long last_step_time; // time stamp in ms of when the last step was taken
};
#endif
现在为Stepper.cpp
/*
Stepper.cpp - - Stepper library for Wiring/Arduino - Version 0.4
Original library (0.1) by Tom Igoe.
Two-wire modifications (0.2) by Sebastian Gassner
Combination version (0.3) by Tom Igoe and David Mellis
Bug fix for four-wire (0.4) by Tom Igoe, bug fix from Noah Shibley
Drives a unipolar or bipolar stepper motor using 2 wires or 4 wires
When wiring multiple stepper motors to a microcontroller,
you quickly run out of output pins, with each motor requiring 4 connections.
By making use of the fact that at any time two of the four motor
coils are the inverse of the other two, the number of
control connections can be reduced from 4 to 2.
A slightly modified circuit around a Darlington transistor array or an L293 H-bridge
connects to only 2 microcontroler pins, inverts the signals received,
and delivers the 4 (2 plus 2 inverted ones) output signals required
for driving a stepper motor.
The sequence of control signals for 4 control wires is as follows:
Step C0 C1 C2 C3
1 1 0 1 0
2 0 1 1 0
3 0 1 0 1
4 1 0 0 1
The sequence of controls signals for 2 control wires is as follows
(columns C1 and C2 from above):
Step C0 C1
1 0 1
2 1 1
3 1 0
4 0 0
The circuits can be found at
http://www.arduino.cc/en/Tutorial/Stepper
*/
#include "WProgram.h"
#include "Stepper.h"
/*
* two-wire constructor.
* Sets which wires should control the motor.
*/
Stepper::Stepper(int number_of_steps, int motor_pin_1, int motor_pin_2)
{
this->step_number = 0; // which step the motor is on
this->speed = 0; // the motor speed, in revolutions per minute
this->direction = 0; // motor direction
this->last_step_time = 0; // time stamp in ms of the last step taken
this->number_of_steps = number_of_steps; // total number of steps for this motor
// Arduino pins for the motor control connection:
this->motor_pin_1 = motor_pin_1;
this->motor_pin_2 = motor_pin_2;
// setup the pins on the microcontroller:
pinMode(this->motor_pin_1, OUTPUT);
pinMode(this->motor_pin_2, OUTPUT);
// When there are only 2 pins, set the other two to 0:
this->motor_pin_3 = 0;
this->motor_pin_4 = 0;
// pin_count is used by the stepMotor() method:
this->pin_count = 2;
}
/*
* constructor for four-pin version
* Sets which wires should control the motor.
*/
Stepper::Stepper(int number_of_steps, int motor_pin_1, int motor_pin_2, int motor_pin_3, int motor_pin_4)
{
this->step_number = 0; // which step the motor is on
this->speed = 0; // the motor speed, in revolutions per minute
this->direction = 0; // motor direction
this->last_step_time = 0; // time stamp in ms of the last step taken
this->number_of_steps = number_of_steps; // total number of steps for this motor
// Arduino pins for the motor control connection:
this->motor_pin_1 = motor_pin_1;
this->motor_pin_2 = motor_pin_2;
this->motor_pin_3 = motor_pin_3;
this->motor_pin_4 = motor_pin_4;
// setup the pins on the microcontroller:
pinMode(this->motor_pin_1, OUTPUT);
pinMode(this->motor_pin_2, OUTPUT);
pinMode(this->motor_pin_3, OUTPUT);
pinMode(this->motor_pin_4, OUTPUT);
// pin_count is used by the stepMotor() method:
this->pin_count = 4;
}
/*
Sets the speed in revs per minute
*/
void Stepper::setSpeed(long whatSpeed)
{
this->step_delay = 60L * 1000L / this->number_of_steps / whatSpeed;
}
/*
Moves the motor steps_to_move steps. If the number is negative,
the motor moves in the reverse direction.
*/
void Stepper::step(int steps_to_move)
{
int steps_left = abs(steps_to_move); // how many steps to take
// determine direction based on whether steps_to_mode is + or -:
if (steps_to_move > 0) {this->direction = 1;}
if (steps_to_move < 0) {this->direction = 0;}
// decrement the number of steps, moving one step each time:
while(steps_left > 0) {
// move only if the appropriate delay has passed:
if (millis() - this->last_step_time >= this->step_delay) {
// get the timeStamp of when you stepped:
this->last_step_time = millis();
// increment or decrement the step number,
// depending on direction:
if (this->direction == 1) {
this->step_number++;
if (this->step_number == this->number_of_steps) {
this->step_number = 0;
}
}
else {
if (this->step_number == 0) {
this->step_number = this->number_of_steps;
}
this->step_number--;
}
// decrement the steps left:
steps_left--;
// step the motor to step number 0, 1, 2, or 3:
stepMotor(this->step_number % 4);
}
}
}
/*
* Moves the motor forward or backwards.
*/
void Stepper::stepMotor(int thisStep)
{
if (this->pin_count == 2) {
switch (thisStep) {
case 0: /* 01 */
digitalWrite(motor_pin_1, LOW);
digitalWrite(motor_pin_2, HIGH);
break;
case 1: /* 11 */
digitalWrite(motor_pin_1, HIGH);
digitalWrite(motor_pin_2, HIGH);
break;
case 2: /* 10 */
digitalWrite(motor_pin_1, HIGH);
digitalWrite(motor_pin_2, LOW);
break;
case 3: /* 00 */
digitalWrite(motor_pin_1, LOW);
digitalWrite(motor_pin_2, LOW);
break;
}
}
if (this->pin_count == 4) {
switch (thisStep) {
case 0: // 1010
digitalWrite(motor_pin_1, HIGH);
digitalWrite(motor_pin_2, LOW);
digitalWrite(motor_pin_3, HIGH);
digitalWrite(motor_pin_4, LOW);
break;
case 1: // 0110
digitalWrite(motor_pin_1, LOW);
digitalWrite(motor_pin_2, HIGH);
digitalWrite(motor_pin_3, HIGH);
digitalWrite(motor_pin_4, LOW);
break;
case 2: //0101
digitalWrite(motor_pin_1, LOW);
digitalWrite(motor_pin_2, HIGH);
digitalWrite(motor_pin_3, LOW);
digitalWrite(motor_pin_4, HIGH);
break;
case 3: //1001
digitalWrite(motor_pin_1, HIGH);
digitalWrite(motor_pin_2, LOW);
digitalWrite(motor_pin_3, LOW);
digitalWrite(motor_pin_4, HIGH);
break;
}
}
}
/*
version() returns the version of the library:
*/
int Stepper::version(void)
{
return 4;
}
答案 0 :(得分：1)
我假设你的意思是quick240主板，因为我找不到quick420。如果我理解你的问题，你试图将步进功能引脚映射到由MPIDE使用的数组值识别的引脚？
引脚8实际上是端口B，引脚0（PB0）转换为C1IO3（原理图上的引脚RB0） 引脚9为端口B，引脚1转换为C0IO3（引脚RB1） 引脚10是PB2转换为C1IO1（引脚RB2） 引脚11是PB3转换为C1IO0（引脚RB3）
C标识卡槽，而IO编号是插槽的引脚。该阵列使用卡槽和引脚作为索引，因此它应该可以帮助你完成大部分工作。
为此，请使用Arduino引脚排列来获取引脚的端口号，然后使用quick240原理图将端口和引脚转换为卡槽和IO号。如果你愿意，你可以在另一个方向翻译。
答案 1 :(得分：0)
看起来Arduino库是为了直接激励步进器的绕组。 BigEasy有一个Allegro步进驱动器芯片，可以进行步进和方向输入。它们是苹果和橘子。您可以将AccelStep库与BigEasy一起使用，它已经被移植到chipKIT。