Question

我正在尝试根据instructions在我的Altera DE2-115 FPGA上运行Linux。显然第一部分有效：

$ quartus_pgm -m jtag -c USB-Blaster[2-2] -o "p;tPad_Selector.sof"
Info: *******************************************************************
Info: Running Quartus Prime Programmer
    Info: Version 16.1.0 Build 196 10/24/2016 SJ Lite Edition
    Info: Copyright (C) 2016  Intel Corporation. All rights reserved.
    Info: Your use of Intel Corporation's design tools, logic functions 
    Info: and other software and tools, and its AMPP partner logic 
    Info: functions, and any output files from any of the foregoing 
    Info: (including device programming or simulation files), and any 
    Info: associated documentation or information are expressly subject 
    Info: to the terms and conditions of the Intel Program License 
    Info: Subscription Agreement, the Intel Quartus Prime License Agreement,
    Info: the Intel MegaCore Function License Agreement, or other 
    Info: applicable license agreement, including, without limitation, 
    Info: that your use is for the sole purpose of programming logic 
    Info: devices manufactured by Intel and sold by Intel or its 
    Info: authorized distributors.  Please refer to the applicable 
    Info: agreement for further details.
    Info: Processing started: Mon Mar 13 17:10:04 2017
Info: Command: quartus_pgm -m jtag -c USB-Blaster[2-2] -o p;tPad_Selector.sof
Info (213045): Using programming cable "USB-Blaster [2-2]"
Inconsistency detected by ld.so: dl-close.c: 811: _dl_close: Assertion `map->l_init_called' failed!
Info (213011): Using programming file tPad_Selector.sof with checksum 0x00BBDF04 for device EP4CE115F29@1
Info (209060): Started Programmer operation at Mon Mar 13 17:10:05 2017
Info (209016): Configuring device index 1
Info (209017): Device 1 contains JTAG ID code 0x020F70DD
Info (209007): Configuration succeeded -- 1 device(s) configured
Info (209011): Successfully performed operation(s)
Info (209061): Ended Programmer operation at Mon Mar 13 17:10:11 2017
Info: Quartus Prime Programmer was successful. 0 errors, 0 warnings
    Info: Peak virtual memory: 453 megabytes
    Info: Processing ended: Mon Mar 13 17:10:11 2017
    Info: Elapsed time: 00:00:07
    Info: Total CPU time (on all processors): 00:00:01

然后我遇到了一些我不明白的问题：

$ nios2-flash-programmer --epcs --base=0x0a001800 tPad_Selector.flash
Using cable "USB-Blaster [2-2]", device 1, instance 0x00
Resetting and pausing target processor: 
OK
No EPCS layout data - looking for section [EPCS-010216]
Unable to use EPCS device
Leaving target processor paused

我在Altera论坛上搜索过它并且无法理解。我应该做什么？

我已经将SD卡格式化为3个分区：ext3，fat和swap。也许SD卡不兼容或者它可能是什么？

调试输出：

$ nios2-flash-programmer --epcs --debug --base=0x0a001800 tPad_Selector.flash
Using cable "USB-Blaster [2-2]", device 1, instance 0x00
Resetting and pausing target processor: 
OK
Processor data bus width is 32 bits
Looking for EPCS registers at address 0x0A001800 (with 32bit alignment)
  Initial values: 0001703A 04C00074 9801483A 9CFFF804 1CE7FF8983FFD1E 0000203A
  Not here: reserved fields are non-zero
Looking for EPCS registers at address 0x0A001900 (with 32bit alignment)
  Initial values: 92400237 4A40100C 483FFD26 90000135 1CE7FF892400237 4A40200C
  Not here: reserved fields are non-zero
Looking for EPCS registers at address 0x0A001A00 (with 32bit alignment)
  Initial values: 108001C4 1004D0FA 002EE03A 003F9C06 1CE7FF8002EE03A 003F9506
  Not here: reserved fields are non-zero
Looking for EPCS registers at address 0x0A001B00 (with 32bit alignment)
  Initial values: 00000000 00000000 00000000 00000000 1CE7FF800000000 00000000
  Not here: SPI_SLAVE_SEL has 0 valid bits (should be between 1 and 16)
Looking for EPCS registers at address 0x0A001C00 (with 32bit alignment)
  Initial values: 00000000 00000000 00000260 00000000 1CE7FF800000000 00000001
  Valid registers found
EPCS signature is 0x16
EPCS identifier is 0x010216
No EPCS layout data - looking for section [EPCS-010216]
Unable to use EPCS device
Leaving target processor paused

Answer 1

您的指示（不是针对DE2-115，而是针对另一个委员会）给出了您所遇到的错误的说明：

 No EPCS layout data - looking for section [EPCS-010216] .

http://www.alterawiki.com/wiki/Linux_with_MMU_on_VEEK/t-Pad#Unfortunately.2C_if_you_don.27t_have_VEEK.2Ft-PAD_kit.2C_but_you_have_DE2-115 ...

注意：执行'nios2-flash-programmer'命令时，可能会出现类似的错误没有EPCS布局数据 - 寻找[EPCS-010216]部分。在这种情况下，请参阅Altera论坛页面上的“nios2-flash-programmer”或“Nios II Flash Programmer用户指南”第22页的“A.非标准Flash存储器”部分。

您是否查看了“Nios II Flash Programmer用户指南”https://www.altera.com/en_US/pdfs/literature/ug/ug_nios2_flash_programmer.pdf部分A. Non-Standard Flash Memories？

使用中的程序在本节中，您需要您正在使用的闪存设备的数据表。确保你完全了解设备的CFI方面。某些CFI闪存设备包含缺少或不正确的CFI表信息。在这种情况下， Nios II Flash Programmer可能会因CFI表中的错误信息而失败。对于这些设备，Nios II Flash Programmer提供以下方法来覆盖CFI表和成功编程闪存...... 始终尝试使用内置识别和在尝试创建覆盖文件之前覆盖。确定闪存编程器是否识别设备使用--debug选项从命令行运行flash编程器。如果闪光灯程序员重写CFI表，flash程序员显示一条消息“内置此设备的覆盖数据”。

原装VEEK / T-pad＆amp; amp;闪存设备是什么？ DE2-115板？

nios2-flash-programmer --epcs --debug --base=0x0a001800 tPad_Selector.flash命令输出什么？

Linux与Altera DE2-115

1 个答案: