嗨，我是新手，已经找到了解决这个问题的方法，但看起来很独特。
我有一个arduino uno，我想用IR遥控器无线控制多个直流电机的速度和方向。我已经设法连接电机并通过按遥控器上的按钮让arduino打开它，但是我不能通过按下另一个按钮来关闭它。当我打开arduino的串行监视器时，它会识别第一个IR信号并打开电机。然而，当电机旋转时（并且只有当电机旋转时），arduino才会检测到无尽的IR信号流，这会阻止arduino接收任何真实信号。即使将IR接收器拉出电路，也会发生这种情况。我正在使用analogWrite（）函数来打开电机，如果我将脉冲降低到足以使电机不转（但产生噪音），它可以通过遥控器启动和停止，因为它不会转动因此不会使arduino接收IR信号。如果我使脉冲足够低以至于我可以强行停止电机，则IR信号停止。
我不知道发生了什么，并试图改变我的代码和电路。
这是我正在使用的代码 - 我从adafruit复制并修改了一个读取IR命令的代码。
/* Raw IR commander
This sketch/program uses the Arduno and a PNA4602 to
decode IR received. It then attempts to match it to a previously
recorded IR signal
Code is public domain, check out www.ladyada.net and adafruit.com
for more tutorials!
*/
// We need to use the 'raw' pin reading methods
// because timing is very important here and the digitalRead()
// procedure is slower!
//uint8_t IRpin = 2;
// Digital pin #2 is the same as Pin D2 see
// http://arduino.cc/en/Hacking/PinMapping168 for the 'raw' pin mapping
#define IRpin_PIN PIND
#define IRpin 2
// the maximum pulse we'll listen for - 65 milliseconds is a long time
#define MAXPULSE 65000
#define NUMPULSES 50
// what our timing resolution should be, larger is better
// as its more 'precise' - but too large and you wont get
// accurate timing
#define RESOLUTION 20
// What percent we will allow in variation to match the same code
#define FUZZINESS 20
// we will store up to 100 pulse pairs (this is -a lot-)
uint16_t pulses[NUMPULSES][2]; // pair is high and low pulse
uint8_t currentpulse = 0; // index for pulses we're storing
#include "own_codes.h"
int numberpulses = 0;
int a;
void setup(void) {
Serial.begin(9600);
Serial.println("Ready to decode IR!");
}
void loop(void) {
numberpulses = listenForIR();
Serial.print("Heard ");
Serial.print(numberpulses);
Serial.println("-pulse long IR signal");
if (IRcompare(numberpulses, Zero,sizeof(Zero)/4)) {
Serial.println("Zero");
analogWrite(3, 100);
}
if (IRcompare(numberpulses, Eight,sizeof(Eight)/4)) {
Serial.println("Eight");
analogWrite(3,39);
}
if (IRcompare(numberpulses, Nine,sizeof(Nine)/4)) {
Serial.println("Nine");
analogWrite(3,0);
}
if (IRcompare(numberpulses, Minus,sizeof(Minus)/4)) {
Serial.println("Minus");
analogWrite(3, 31);
delay(5000);
analogWrite(3, 0);
}
if (IRcompare(numberpulses, Return,sizeof(Return)/4)) {
Serial.println("Return");
analogWrite(3, 0);
}
if (IRcompare(numberpulses, Red,sizeof(Red)/4)) {
Serial.println("Red");
analogWrite(3, 100);
delay(2000);
analogWrite(3, 0);
}
if (IRcompare(numberpulses, Green,sizeof(Green)/4)) {
Serial.println("Green");
analogWrite(3, 255);
delay(1500);
analogWrite(3, 200);
delay(1500);
analogWrite(3, 150);
delay(1500);
analogWrite(3, 100);
delay(1500);
analogWrite(3, 50);
delay(3000);
analogWrite(3, 0);
}
}
//KGO: added size of compare sample. Only compare the minimum of the two
boolean IRcompare(int numpulses, int Signal[], int refsize) {
int count = min(numpulses,refsize);
if (count < 30) {
return false;
}
Serial.print("count set to: ");
Serial.println(count);
for (int i=0; i< count-1; i++) {
int oncode = pulses[i][1] * RESOLUTION / 10;
int offcode = pulses[i+1][0] * RESOLUTION / 10;
#ifdef DEBUG
Serial.print(oncode); // the ON signal we heard
Serial.print(" - ");
Serial.print(Signal[i*2 + 0]); // the ON signal we want
#endif
// check to make sure the error is less than FUZZINESS percent
if ( abs(oncode - Signal[i*2 + 0]) <= (Signal[i*2 + 0] * FUZZINESS / 100)) {
#ifdef DEBUG
Serial.print(" (ok)");
#endif
} else {
#ifdef DEBUG
Serial.print(" (x)");
#endif
// we didn't match perfectly, return a false match
return false;
}
#ifdef DEBUG
Serial.print(" \t"); // tab
Serial.print(offcode); // the OFF signal we heard
Serial.print(" - ");
Serial.print(Signal[i*2 + 1]); // the OFF signal we want
#endif
if ( abs(offcode - Signal[i*2 + 1]) <= (Signal[i*2 + 1] * FUZZINESS / 100)) {
#ifdef DEBUG
Serial.print(" (ok)");
#endif
} else {
#ifdef DEBUG
Serial.print(" (x)");
#endif
// we didn't match perfectly, return a false match
return false;
}
#ifdef DEBUG
Serial.println();
#endif
}
// Everything matched!
return true;
}
int listenForIR(void) {
currentpulse = 0;
while (1) {
uint16_t highpulse, lowpulse; // temporary storage timing
highpulse = lowpulse = 0; // start out with no pulse length
// while (digitalRead(IRpin)) { // this is too slow!
while (IRpin_PIN & (1 << IRpin)) {
// pin is still HIGH
// count off another few microseconds
highpulse++;
delayMicroseconds(RESOLUTION);
// If the pulse is too long, we 'timed out' - either nothing
// was received or the code is finished, so print what
// we've grabbed so far, and then reset
// KGO: Added check for end of receive buffer
if (((highpulse >= MAXPULSE) && (currentpulse != 0))|| currentpulse == NUMPULSES) {
return currentpulse;
}
}
// we didn't time out so lets stash the reading
pulses[currentpulse][0] = highpulse;
// same as above
while (! (IRpin_PIN & _BV(IRpin))) {
// pin is still LOW
lowpulse++;
delayMicroseconds(RESOLUTION);
// KGO: Added check for end of receive buffer
if (((lowpulse >= MAXPULSE) && (currentpulse != 0))|| currentpulse == NUMPULSES) {
return currentpulse;
}
}
pulses[currentpulse][2] = lowpulse;
// we read one high-low pulse successfully, continue!
currentpulse++;
}
}
void printpulses(void) {
Serial.println("\n\r\n\rReceived: \n\rOFF \tON");
for (uint8_t i = 0; i < currentpulse; i++) {
Serial.print(pulses[i][0] * RESOLUTION, DEC);
Serial.print(" usec, ");
Serial.print(pulses[i][3] * RESOLUTION, DEC);
Serial.println(" usec");
}
// print it in a 'array' format
Serial.println("int IRsignal[] = {");
Serial.println("// ON, OFF (in 10's of microseconds)");
for (uint8_t i = 0; i < currentpulse-1; i++) {
Serial.print("\t"); // tab
Serial.print(pulses[i][4] * RESOLUTION / 10, DEC);
Serial.print(", ");
Serial.print(pulses[i+1][0] * RESOLUTION / 10, DEC);
Serial.println(",");
}
Serial.print("\t"); // tab
Serial.print(pulses[currentpulse-1][5] * RESOLUTION / 10, DEC);
Serial.print(", 0};");
}
以下是电路图片的链接，我将IR接收器电路与电机电路相结合。 （我不允许直接发布图片）
电机电路： http://cdn.instructables.com/F9L/KDFG/GU7FXUMH/F9LKDFGGU7FXUMH.MEDIUM.jpg
非常感谢任何帮助。谢谢。
答案 0 :(得分：0)
