我正在尝试让PIC24与ADC转换器配合使用，将电位器用作音量旋钮，但为此，我需要读出ADC，代码不允许我建立。请参阅问题的底部。接线正确完成。
MPlab在main.c中没有显示错误，但是当我构建项目时，user.c中出现了一些错误。
我将PIC24FJ64GB002连接在带有一些按钮和mdog显示屏的电路板上。
的main.c
#include <p24FJ64GB002.h>
//#include <pic.h>
#include "DogM.h"
#include <stdlib.h>
#include <time.h>
#include <p24fxxxx.h>
//#include <user.c>
_CONFIG1( JTAGEN_OFF & //JTAG port is disabled
GCP_OFF & //GSP Memory Code Protection OFF
GWRP_OFF & //GCC Flash Write Protection OFF
//COE_OFF & //
FWDTEN_OFF & //Watchdog Timer OFF
ICS_PGx1) //debug over PGD1 and PGC1
_CONFIG2( FNOSC_FRCPLL & //Internal FRC with PLL
OSCIOFNC_ON & //RA3 is clk out (fosc/2)
POSCMOD_NONE & //Primary oscillator disabled
I2C1SEL_PRI) //Use default SCL1/SDA1 pins
#define VREG33_DIR TRISAbits.TRISA0
#define VREG33_EN LATAbits.LATA0
#define MODE_LED_DIR TRISAbits.TRISA1
#define MODE_LED LATAbits.LATA1
#pragma code
int main(void)
{
// Set up the hardware of the display
InitApp();
mdog_Init(0x81, 0x19);
init_adc();
clearDisplay();
// Initscreen clears a internal bitmap used
// in drawScreen to send out to the display
initScreen();
// Beware writeString will write directly to the display
// the internal bitmap is not modified.
CLKDIVbits.RCDIV0=0; //clock divider to 0
AD1PCFG = 0xFFFF; // Default all pins to digital
OSCCONbits.SOSCEN=0; //Disables the secondary oscilator
MODE_LED_DIR = 0; //sets the Mode LED pin RA1 as output
MODE_LED = 0; //turns LED off
VREG33_DIR =0; //sets teh VREG pin RA0 as output
VREG33_EN = 1; //turns on the voltage regulator
unsigned long int i,voltage;
//////////////////////////////////////////////////////////////
///////////////ADC config//////////////////////////////////
AD1PCFGbits.PCFG12=0; //configure RB12 as analog
AD1CON1bits.SSRC = 0b111; // SSRC<3:0> = 111 implies internal
// counter ends sampling and starts
// converting.
AD1CON3 = 0x1F02; // Sample time = 31Tad,
// Tad = 2 Tcy
AD1CHS =12; //ADC channel select 12
AD1CON1bits.ADON =1; // turn ADC on
///FOREVER LOOP///////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////
while(1)
{
//this just gives us a little delay between measurements
i =0xFFFFF; //sets i to 1048575
while (i--); //delay function
//start a measurement with the ADC
AD1CON1bits.DONE=0; //resets DONE bit
AD1CON1bits.SAMP=1; //start sample
while(AD1CON1bits.DONE==0); //wait for conversion to finish
//get the measurement and use it to control the LED
voltage = ADC1BUF0; //get the voltage measurement
//if (voltage > 0x1D1) MODE_LED = 1; //enable LED if measurement is > 3volts
//else MODE_LED = 0; //disable LED if less than 3volts
writeString(boldFont, 0x0, 0x3, "Hallo");
}
}
user.c的
/******************************************************************************/
/* Files to Include */
/******************************************************************************/
/* Device header file */
#if defined(__PIC24E__)
#include <p24Exxxx.h>
#elif defined (__PIC24F__)
//#include <p24Fxxxx.h>
#include <p24FJ64GB002.h>
#elif defined(__PIC24H__)
#include <p24Hxxxx.h>
#endif
//#include "user.h" /* variables/params used by user.c */
/******************************************************************************/
/* User Functions */
/******************************************************************************/
/* <Initialize variables in user.h and insert code for user algorithms.> */
/* TODO Initialize User Ports/Peripherals/Project here */
/**
* Initialize the Analog to Digital Converter.
*/
/**/void init_adc(void)
{
TRISAbits.TRISA1 = 0b1; // set pin as input
ANCON0bits.ANSEL1 = 0b1; // set pin as analog
ADCON1bits.VCFG = 0b00; // set v+ reference to Vdd
ADCON1bits.VNCFG = 0b0; // set v- reference to GND
ADCON1bits.CHSN = 0b000;// set negative input to GND
ADCON2bits.ADFM = 0b1; // right justify the output
ADCON2bits.ACQT = 0b110;// 16 TAD
ADCON2bits.ADCS = 0b101;// use Fosc/16 for clock source
ADCON0bits.ADON = 0b1; // turn on the ADC
}
/**
* Preform an analog to digital conversion.
* @param channel The ADC input channel to use.
* @return The value of the conversion.
*/
/* uint16_t adc_convert(uint8_t channel)
{
ADCON0bits.CHS = channel; // select the given channel
ADCON0bits.GO = 0b1; // start the conversion
while(ADCON0bits.DONE); // wait for the conversion to finish
return (ADRESH<<8)|ADRESL; // return the result
} */
void InitApp(void) {
// Setup analog functionality and port direction
AD1PCFGL = 0xFFFF; // Make analog pins digital
// Initialize peripherals
// set up I/O ports
TRISB = 0x0000; // all pins as output
LATB = 0x0; // all set to 0
// CN interrupts
CNEN1 = 0; /* Disable all CN */
CNEN2 = 0;
init_adc();
CNEN1bits.CN2IE = 1;
CNEN1bits.CN3IE = 1;
CNEN2bits.CN29IE = 1;
CNEN2bits.CN30IE = 1;
IPC4bits.CNIP0 = 1;
IPC4bits.CNIP1 = 0;
IPC4bits.CNIP2 = 0;
IFS1bits.CNIF = 0;
IEC1bits.CNIE = 1;
}
构建时记录：
"D:\Program Files (x86)\Microchip\xc16\v1.23\bin\xc16-gcc.exe" user.c -o build/default/production/user.o -c -mcpu=24FJ64GB002 -MMD -MF "build/default/production/user.o.d" -g -omf=elf -O0 -I"Dogm128x64" -msmart-io=1 -msfr-warn=off
user.c: In function 'init_adc':
user.c:30:5: error: 'ANCON0bits' undeclared (first use in this function)
user.c:30:5: note: each undeclared identifier is reported only once for each function it appears in
user.c:31:5: error: 'ADCON1bits' undeclared (first use in this function)
user.c:34:5: error: 'ADCON2bits' undeclared (first use in this function)
user.c:37:5: error: 'ADCON0bits' undeclared (first use in this function)
make[2]: *** [build/default/production/user.o] Error 255
make[1]: *** [.build-conf] Error 2
make: *** [.build-impl] Error 2
make[2]: Leaving directory `D:/Dropbox/HvA/Embedded/Potmeter'
make[1]: Leaving directory `D:/Dropbox/HvA/Embedded/Potmeter'
BUILD FAILED (exit value 2, total time: 254ms)
答案 0 :(得分：1)
我认为@ElderBug是对的。你混合了所有的名字。错误告诉您名称不存在。然后检查其他名称，例如AD1CON0bits
Microchip对每个外设都有一个manuel参考。它提供了比普通数据表更多的提示
对于您的MCU，您可以在此处找到它：http://ww1.microchip.com/downloads/en/DeviceDoc/39705b.pdf