Question

我只是想在CWP中存储第二个IP地址。我使用了位于管理面板中的IP管理器。他创建了以下文件：

ifcfg-：1 具有以下内容

DEVICE=:1
TYPE=Ethernet
ONBOOT=yes
NM_CONTROLLED=no
BOOTPROTO=static
IPADDR=5.199.130.204
NETMASK=255.255.255.255
GATEWAY=91.194.84.1

当我输入命令时

service network restart
I get the following message
[root@cpanel network-scripts]# service network restart
Restarting network (via systemctl):
** (pkttyagent:19657): WARNING **: 18:17:04.966: Unable to register authentication agent: GDBus.Error:org.freedesktop.PolicyKit1.Error.Failed: Cannot determine user of subject
Error registering authentication agent: GDBus.Error:org.freedesktop.PolicyKit1.Error.Failed: Cannot determine user of subject (polkit-error-quark, 0)
[ OK ]

但是使用命令ifconfig我看不到新的IP地址

[root@cpanel network-scripts]# ifconfig
docker0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 172.17.0.1 netmask 255.255.0.0 broadcast 172.17.255.255
ether 02:42:80:6b:74:bf txqueuelen 0 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
enp1s0f0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 91.194.84.77 netmask 255.255.255.0 broadcast 91.194.84.255
inet6 fe80::225:90ff:fee1:a1cc prefixlen 64 scopeid 0x20<link>
ether 00:25:90:e1:a1:cc txqueuelen 1000 (Ethernet)
RX packets 896454492 bytes 77246656595 (71.9 GiB)
RX errors 0 dropped 121675 overruns 21 frame 0
TX packets 328489556 bytes 321552938430 (299.4 GiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device memory 0xfea80000-feafffff
enp1s0f1: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 00:25:90:e1:a1:cd txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device memory 0xfe980000-fe9fffff
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 28795464 bytes 8187828621 (7.6 GiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 28795464 bytes 8187828621 (7.6 GiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
virbr0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.122.1 netmask 255.255.255.0 broadcast 192.168.122.255
ether 52:54:00:d8:74:c8 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

我想将IP 5.199.130.204添加到我的服务器，然后将其用于2个名称服务器。但是，使用ifconfig命令输入后，我无法识别该IP。

我做错了吗？

Answer 1

ifconfig仅显示一个结果

检查使用 id address或nmcli con show conname

可以附加 nmcli con mod +ipv4.addresses ip/prefix

或

附加到ifcfg-*

IPADDR1=ip PREFIX1=prefix，但不建议直接更改

Answer 2

您应该修复正在出现的polkitd问题

groupadd -g 23 nohidproc usermod -a -G nohidproc polkitd 挂载-o remount，rw，hidepid = 2，gid = nohidproc / proc systemctl重新启动polkit 在/ etc / fstab中也添加以下内容 echo“ proc / proc proc默认值，hidepid = 2，gid = nohidproc 0 0” >> / etc / fstab

将第二个IP4添加到服务器（CentOS）

2 个答案: