我遇到了一个奇怪的问题。我使用Eclipse Oxygen.2，Windows 10，J-linker，STM32L4R5ZI，STM32CubeMX V1.0 ver 4.26.0，arm-none-eabi-gcc（适用于ARM嵌入式处理器的GNU工具）4.9.3 20150529（发行版）[ARM /嵌入式4_9分支修订版227977]
问题：每当我想使用malloc函数时，我都会以WWDG_IRQHandler()（Default_Handler：Infinit_Loop）结尾，并且从不退回{{1} }。
链接描述文件：
malloc主要功能：
/* Specify the memory areas */
MEMORY
{
RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 640K
FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 2048K
}
_sbrk：
int main(void)
{
HAL_Init();
SystemClock_Config();
uint8_t *tab = malloc(100);
MX_GPIO_Init();
MX_TIM1_Init();
HAL_TIM_OC_Start_IT(&htim1, TIM_CHANNEL_1);
HAL_GPIO_TogglePin(GPIOB, GPIO_PIN_7);
while (1)
{
}
}
脚本： Sections.ld
_sbrk(int incr)
{
extern char _Heap_Begin; // Defined by the linker.
extern char _Heap_Limit; // Defined by the linker.
static char* current_heap_end;
char* current_block_address;
if (current_heap_end == 0)
{
current_heap_end = &_Heap_Begin;
}
current_block_address = current_heap_end;
// Need to align heap to word boundary, else will get
// hard faults on Cortex-M0. So we assume that heap starts on
// word boundary, hence make sure we always add a multiple of
// 4 to it.
incr = (incr + 3) & (~3); // align value to 4
if (current_heap_end + incr > &_Heap_Limit)
{
// Some of the libstdc++-v3 tests rely upon detecting
// out of memory errors, so do not abort here.
#if 0
extern void abort (void);
_write (1, "_sbrk: Heap and stack collision\n", 32);
abort ();
#else
// Heap has overflowed
errno = ENOMEM;
return (caddr_t) - 1;
#endif
}
current_heap_end += incr;
return (caddr_t) current_block_address;
}
STM32L4R5ZI Flash.ld
/*
* Default linker script for Cortex-M (it includes specifics for STM32F[34]xx).
*
* To make use of the multi-region initialisations, define
* OS_INCLUDE_STARTUP_INIT_MULTIPLE_RAM_SECTIONS for the _startup.c file.
*/
/*
* The '__stack' definition is required by crt0, do not remove it.
*/
__stack = ORIGIN(RAM) + LENGTH(RAM);
_estack = __stack; /* STM specific definition */
/*
* Default stack sizes.
* These are used by the startup in order to allocate stacks
* for the different modes.
*/
__Main_Stack_Size = 1024 ;
PROVIDE ( _Main_Stack_Size = __Main_Stack_Size ) ;
__Main_Stack_Limit = __stack - __Main_Stack_Size ;
/* "PROVIDE" allows to easily override these values from an
* object file or the command line. */
PROVIDE ( _Main_Stack_Limit = __Main_Stack_Limit ) ;
/*
* There will be a link error if there is not this amount of
* RAM free at the end.
*/
_Minimum_Stack_Size = 256 ;
/*
* Default heap definitions.
* The heap start immediately after the last statically allocated
* .sbss/.noinit section, and extends up to the main stack limit.
*/
PROVIDE ( _Heap_Begin = _end_noinit ) ;
PROVIDE ( _Heap_Limit = __stack - __Main_Stack_Size ) ;
/*
* The entry point is informative, for debuggers and simulators,
* since the Cortex-M vector points to it anyway.
*/
ENTRY(_start)
/* Sections Definitions */
SECTIONS
{
/*
* For Cortex-M devices, the beginning of the startup code is stored in
* the .isr_vector section, which goes to FLASH.
*/
.isr_vector : ALIGN(4)
{
FILL(0xFF)
__vectors_start = ABSOLUTE(.) ;
__vectors_start__ = ABSOLUTE(.) ; /* STM specific definition */
KEEP(*(.isr_vector)) /* Interrupt vectors */
KEEP(*(.cfmconfig)) /* Freescale configuration words */
/*
* This section is here for convenience, to store the
* startup code at the beginning of the flash area, hoping that
* this will increase the readability of the listing.
*/
*(.after_vectors .after_vectors.*) /* Startup code and ISR */
} >FLASH
.inits : ALIGN(4)
{
/*
* Memory regions initialisation arrays.
*
* Thee are two kinds of arrays for each RAM region, one for
* data and one for bss. Each is iterrated at startup and the
* region initialisation is performed.
*
* The data array includes:
* - from (LOADADDR())
* - region_begin (ADDR())
* - region_end (ADDR()+SIZEOF())
*
* The bss array includes:
* - region_begin (ADDR())
* - region_end (ADDR()+SIZEOF())
*
* WARNING: It is mandatory that the regions are word aligned,
* since the initialisation code works only on words.
*/
__data_regions_array_start = .;
LONG(LOADADDR(.data));
LONG(ADDR(.data));
LONG(ADDR(.data)+SIZEOF(.data));
LONG(LOADADDR(.data_CCMRAM));
LONG(ADDR(.data_CCMRAM));
LONG(ADDR(.data_CCMRAM)+SIZEOF(.data_CCMRAM));
__data_regions_array_end = .;
__bss_regions_array_start = .;
LONG(ADDR(.bss));
LONG(ADDR(.bss)+SIZEOF(.bss));
LONG(ADDR(.bss_CCMRAM));
LONG(ADDR(.bss_CCMRAM)+SIZEOF(.bss_CCMRAM));
__bss_regions_array_end = .;
/* End of memory regions initialisation arrays. */
/*
* These are the old initialisation sections, intended to contain
* naked code, with the prologue/epilogue added by crti.o/crtn.o
* when linking with startup files. The standalone startup code
* currently does not run these, better use the init arrays below.
*/
KEEP(*(.init))
KEEP(*(.fini))
. = ALIGN(4);
/*
* The preinit code, i.e. an array of pointers to initialisation
* functions to be performed before constructors.
*/
PROVIDE_HIDDEN (__preinit_array_start = .);
/*
* Used to run the SystemInit() before anything else.
*/
KEEP(*(.preinit_array_sysinit .preinit_array_sysinit.*))
/*
* Used for other platform inits.
*/
KEEP(*(.preinit_array_platform .preinit_array_platform.*))
/*
* The application inits. If you need to enforce some order in
* execution, create new sections, as before.
*/
KEEP(*(.preinit_array .preinit_array.*))
PROVIDE_HIDDEN (__preinit_array_end = .);
. = ALIGN(4);
/*
* The init code, i.e. an array of pointers to static constructors.
*/
PROVIDE_HIDDEN (__init_array_start = .);
KEEP(*(SORT(.init_array.*)))
KEEP(*(.init_array))
PROVIDE_HIDDEN (__init_array_end = .);
. = ALIGN(4);
/*
* The fini code, i.e. an array of pointers to static destructors.
*/
PROVIDE_HIDDEN (__fini_array_start = .);
KEEP(*(SORT(.fini_array.*)))
KEEP(*(.fini_array))
PROVIDE_HIDDEN (__fini_array_end = .);
} >FLASH
/*
* For some STRx devices, the beginning of the startup code
* is stored in the .flashtext section, which goes to FLASH.
*/
.flashtext : ALIGN(4)
{
*(.flashtext .flashtext.*) /* Startup code */
} >FLASH
/*
* The program code is stored in the .text section,
* which goes to FLASH.
*/
.text : ALIGN(4)
{
*(.text .text.*) /* all remaining code */
/* read-only data (constants) */
*(.rodata .rodata.* .constdata .constdata.*)
*(vtable) /* C++ virtual tables */
KEEP(*(.eh_frame*))
/*
* Stub sections generated by the linker, to glue together
* ARM and Thumb code. .glue_7 is used for ARM code calling
* Thumb code, and .glue_7t is used for Thumb code calling
* ARM code. Apparently always generated by the linker, for some
* architectures, so better leave them here.
*/
*(.glue_7)
*(.glue_7t)
} >FLASH
/* ARM magic sections */
.ARM.extab : ALIGN(4)
{
*(.ARM.extab* .gnu.linkonce.armextab.*)
} > FLASH
. = ALIGN(4);
__exidx_start = .;
.ARM.exidx : ALIGN(4)
{
*(.ARM.exidx* .gnu.linkonce.armexidx.*)
} > FLASH
__exidx_end = .;
. = ALIGN(4);
_etext = .;
__etext = .;
/* MEMORY_ARRAY */
/*
.ROarraySection :
{
*(.ROarraySection .ROarraySection.*)
} >MEMORY_ARRAY
*/
/*
* The secondary initialised data section.
*/
.data_CCMRAM : ALIGN(4)
{
FILL(0xFF)
*(.data.CCMRAM .data.CCMRAM.*)
. = ALIGN(4) ;
} > CCMRAM AT>FLASH
/*
* This address is used by the startup code to
* initialise the .data section.
*/
_sidata = LOADADDR(.data);
/*
* The initialised data section.
*
* The program executes knowing that the data is in the RAM
* but the loader puts the initial values in the FLASH (inidata).
* It is one task of the startup to copy the initial values from
* FLASH to RAM.
*/
.data : ALIGN(4)
{
FILL(0xFF)
/* This is used by the startup code to initialise the .data section */
_sdata = . ; /* STM specific definition */
__data_start__ = . ;
*(.data_begin .data_begin.*)
*(.data .data.*)
*(.data_end .data_end.*)
. = ALIGN(4);
/* This is used by the startup code to initialise the .data section */
_edata = . ; /* STM specific definition */
__data_end__ = . ;
} >RAM AT>FLASH
/*
* The uninitialised data sections. NOLOAD is used to avoid
* the "section `.bss' type changed to PROGBITS" warning
*/
/* The secondary uninitialised data section. */
.bss_CCMRAM (NOLOAD) : ALIGN(4)
{
*(.bss.CCMRAM .bss.CCMRAM.*)
} > CCMRAM
/* The primary uninitialised data section. */
.bss (NOLOAD) : ALIGN(4)
{
__bss_start__ = .; /* standard newlib definition */
_sbss = .; /* STM specific definition */
*(.bss_begin .bss_begin.*)
*(.bss .bss.*)
*(COMMON)
*(.bss_end .bss_end.*)
. = ALIGN(4);
__bss_end__ = .; /* standard newlib definition */
_ebss = . ; /* STM specific definition */
} >RAM
.noinit_CCMRAM (NOLOAD) : ALIGN(4)
{
*(.noinit.CCMRAM .noinit.CCMRAM.*)
} > CCMRAM
.noinit (NOLOAD) : ALIGN(4)
{
_noinit = .;
*(.noinit .noinit.*)
. = ALIGN(4) ;
_end_noinit = .;
} > RAM
/* Mandatory to be word aligned, _sbrk assumes this */
PROVIDE ( end = _end_noinit ); /* was _ebss */
PROVIDE ( _end = _end_noinit );
PROVIDE ( __end = _end_noinit );
PROVIDE ( __end__ = _end_noinit );
/*
* Used for validation only, do not allocate anything here!
*
* This is just to check that there is enough RAM left for the Main
* stack. It should generate an error if it's full.
*/
._check_stack : ALIGN(4)
{
. = . + _Minimum_Stack_Size ;
} >RAM
/*
* The FLASH Bank1.
* The C or assembly source must explicitly place the code
* or data there using the "section" attribute.
*/
.b1text : ALIGN(4)
{
*(.b1text) /* remaining code */
*(.b1rodata) /* read-only data (constants) */
*(.b1rodata.*)
} >FLASHB1
/*
* The EXTMEM.
* The C or assembly source must explicitly place the code or data there
* using the "section" attribute.
*/
/* EXTMEM Bank0 */
.eb0text : ALIGN(4)
{
*(.eb0text) /* remaining code */
*(.eb0rodata) /* read-only data (constants) */
*(.eb0rodata.*)
} >EXTMEMB0
/* EXTMEM Bank1 */
.eb1text : ALIGN(4)
{
*(.eb1text) /* remaining code */
*(.eb1rodata) /* read-only data (constants) */
*(.eb1rodata.*)
} >EXTMEMB1
/* EXTMEM Bank2 */
.eb2text : ALIGN(4)
{
*(.eb2text) /* remaining code */
*(.eb2rodata) /* read-only data (constants) */
*(.eb2rodata.*)
} >EXTMEMB2
/* EXTMEM Bank0 */
.eb3text : ALIGN(4)
{
*(.eb3text) /* remaining code */
*(.eb3rodata) /* read-only data (constants) */
*(.eb3rodata.*)
} >EXTMEMB3
/* After that there are only debugging sections. */
/* This can remove the debugging information from the standard libraries */
/*
DISCARD :
{
libc.a ( * )
libm.a ( * )
libgcc.a ( * )
}
*/
/* Stabs debugging sections. */
.stab 0 : { *(.stab) }
.stabstr 0 : { *(.stabstr) }
.stab.excl 0 : { *(.stab.excl) }
.stab.exclstr 0 : { *(.stab.exclstr) }
.stab.index 0 : { *(.stab.index) }
.stab.indexstr 0 : { *(.stab.indexstr) }
.comment 0 : { *(.comment) }
/*
* DWARF debug sections.
* Symbols in the DWARF debugging sections are relative to the beginning
* of the section so we begin them at 0.
*/
/* DWARF 1 */
.debug 0 : { *(.debug) }
.line 0 : { *(.line) }
/* GNU DWARF 1 extensions */
.debug_srcinfo 0 : { *(.debug_srcinfo) }
.debug_sfnames 0 : { *(.debug_sfnames) }
/* DWARF 1.1 and DWARF 2 */
.debug_aranges 0 : { *(.debug_aranges) }
.debug_pubnames 0 : { *(.debug_pubnames) }
/* DWARF 2 */
.debug_info 0 : { *(.debug_info .gnu.linkonce.wi.*) }
.debug_abbrev 0 : { *(.debug_abbrev) }
.debug_line 0 : { *(.debug_line) }
.debug_frame 0 : { *(.debug_frame) }
.debug_str 0 : { *(.debug_str) }
.debug_loc 0 : { *(.debug_loc) }
.debug_macinfo 0 : { *(.debug_macinfo) }
/* SGI/MIPS DWARF 2 extensions */
.debug_weaknames 0 : { *(.debug_weaknames) }
.debug_funcnames 0 : { *(.debug_funcnames) }
.debug_typenames 0 : { *(.debug_typenames) }
.debug_varnames 0 : { *(.debug_varnames) }
}
答案 0 :(得分：1)
您不一定要进入WWDG_IRQ函数。您将获得默认的中断处理程序功能，即无限循环。此功能是STMCubeMX设置的许多处理器异常的目标。如果由于访问不存在的存储器位置而导致总线故障中断，则将在同一位置结束。我已经在许多调试器上看到，他们会说您在WWDG_IRQ函数中，而不管实际上是哪个中断/异常将您带到了那里。
我希望在您的malloc函数中，您试图访问非法地址并生成处理器异常。只需单步操作该功能，就可以定位问题。
答案 1 :(得分：0)
我不得不更改STM32L4R5ZI_Flash脚本并删除section脚本（所以我现在仅使用一个脚本）。
不幸的是，_Heap_Begin和_Heap_Limit接受了我无法解释的估值，但至少可以使用。
更改后的脚本：
/*
*****************************************************************************
**
** File : LinkerScript.ld
**
** Abstract : Linker script for STM32L4R5ZITx Device with
** 2048KByte FLASH, 640KByte RAM
**
** Set heap size, stack size and stack location according
** to application requirements.
**
** Set memory bank area and size if external memory is used.
**
** Target : STMicroelectronics STM32
**
**
** Distribution: The file is distributed as is, without any warranty
** of any kind.
**
** (c)Copyright Ac6.
** You may use this file as-is or modify it according to the needs of your
** project. Distribution of this file (unmodified or modified) is not
** permitted. Ac6 permit registered System Workbench for MCU users the
** rights to distribute the assembled, compiled & linked contents of this
** file as part of an application binary file, provided that it is built
** using the System Workbench for MCU toolchain.
**
*****************************************************************************
*/
/* Entry Point */
ENTRY(Reset_Handler)
/* Highest address of the user mode stack */
_estack = 0x200A0000; /* end of RAM */
/* Generate a link error if heap and stack don't fit into RAM */
_Min_Heap_Size = 0x2000; /* required amount of heap */
_Min_Stack_Size = 0x4000; /* required amount of stack */
/* Specify the memory areas */
MEMORY
{
RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 640K
FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 2048K
}
/* Define output sections */
SECTIONS
{
/* The startup code goes first into FLASH */
.isr_vector :
{
. = ALIGN(8);
KEEP(*(.isr_vector)) /* Startup code */
. = ALIGN(8);
} >FLASH
/* The program code and other data goes into FLASH */
.text :
{
. = ALIGN(8);
*(.text) /* .text sections (code) */
*(.text*) /* .text* sections (code) */
*(.glue_7) /* glue arm to thumb code */
*(.glue_7t) /* glue thumb to arm code */
*(.eh_frame)
KEEP (*(.init))
KEEP (*(.fini))
. = ALIGN(8);
_etext = .; /* define a global symbols at end of code */
} >FLASH
/* Constant data goes into FLASH */
.rodata :
{
. = ALIGN(8);
*(.rodata) /* .rodata sections (constants, strings, etc.) */
*(.rodata*) /* .rodata* sections (constants, strings, etc.) */
. = ALIGN(8);
} >FLASH
.ARM.extab :
{
. = ALIGN(8);
*(.ARM.extab* .gnu.linkonce.armextab.*)
. = ALIGN(8);
} >FLASH
.ARM : {
. = ALIGN(8);
__exidx_start = .;
*(.ARM.exidx*)
__exidx_end = .;
. = ALIGN(8);
} >FLASH
.preinit_array :
{
. = ALIGN(8);
PROVIDE_HIDDEN (__preinit_array_start = .);
KEEP (*(.preinit_array*))
PROVIDE_HIDDEN (__preinit_array_end = .);
. = ALIGN(8);
} >FLASH
.init_array :
{
. = ALIGN(8);
PROVIDE_HIDDEN (__init_array_start = .);
KEEP (*(SORT(.init_array.*)))
KEEP (*(.init_array*))
PROVIDE_HIDDEN (__init_array_end = .);
. = ALIGN(8);
} >FLASH
.fini_array :
{
. = ALIGN(8);
PROVIDE_HIDDEN (__fini_array_start = .);
KEEP (*(SORT(.fini_array.*)))
KEEP (*(.fini_array*))
PROVIDE_HIDDEN (__fini_array_end = .);
. = ALIGN(8);
} >FLASH
/* used by the startup to initialize data */
_sidata = LOADADDR(.data);
/* Initialized data sections goes into RAM, load LMA copy after code */
.data :
{
. = ALIGN(8);
_sdata = .; /* create a global symbol at data start */
*(.data) /* .data sections */
*(.data*) /* .data* sections */
. = ALIGN(8);
_edata = .; /* define a global symbol at data end */
} >RAM AT> FLASH
/* Uninitialized data section */
. = ALIGN(4);
.bss :
{
/* This is used by the startup in order to initialize the .bss secion */
_sbss = .; /* define a global symbol at bss start */
__bss_start__ = _sbss;
*(.bss)
*(.bss*)
*(COMMON)
. = ALIGN(4);
_ebss = .; /* define a global symbol at bss end */
__bss_end__ = _ebss;
} >RAM
/* User_heap_stack section, used to check that there is enough RAM left */
._user_heap_stack :
{
. = ALIGN(8);
PROVIDE ( end = . );
PROVIDE ( _end = . );
. = . + _Min_Heap_Size;
. = . + _Min_Stack_Size;
. = ALIGN(8);
} >RAM
_Heap_Begin = __bss_end__ ;
_Heap_Limit = _Heap_Begin + _Min_Heap_Size;
/* Remove information from the standard libraries */
/DISCARD/ :
{
libc.a ( * )
libm.a ( * )
libgcc.a ( * )
}
.ARM.attributes 0 : { *(.ARM.attributes) }
}