我正在使用来自https://reference.digilentinc.com/reference/programmable-logic/nexys-2/start的RS232接口参考组件和一个示例代码：
-------------------------------------------------------------------------
-- main.vhd
-------------------------------------------------------------------------
-- Author: Dan Pederson
-- Copyright 2004 Digilent, Inc.
-------------------------------------------------------------------------
-- Description: This file tests the included UART component by
-- sending data in serial form through the UART to
-- change it to parallel form, and then sending the
-- resultant data back through the UART to determine if
-- the signal is corrupted or not. When the serial
-- information is converted into parallel information,
-- the data byte is displayed on the 8 LEDs on the
-- system board.
--
-- NOTE: Not all mapped signals are used in this test.
-- The signals were mapped to ease the modification of
-- test program.
-------------------------------------------------------------------------
-- Revision History:
-- 07/30/04 (DanP) Created
-- 05/26/05 (DanP) Modified for Pegasus board/Updated commenting style
-- 06/07/05 (DanP) LED scancode display added
-------------------------------------------------------------------------
library IEEE;
use IEEE.STD_LOGIC_1164.ALL;
use IEEE.STD_LOGIC_ARITH.ALL;
use IEEE.STD_LOGIC_UNSIGNED.ALL;
-------------------------------------------------------------------------
--
--Title: Main entity
--
--Inputs: 3 : RXD
-- CLK
-- RST
--
--Outputs: 1 : TXD
-- LEDS
--
--Description: This describes the main entity that tests the included
-- UART component. The LEDS signals are used to
-- display the data byte on the LEDs, so it is set equal to
-- the dbOutSig. Technically, the dbOutSig is the scan code
-- backwards, which explains why the LEDs are mapped
-- backwards to the dbOutSig.
--
-------------------------------------------------------------------------
entity DataCntrl is
Port ( TXD : out std_logic := '1';
RXD : in std_logic := '1';
CLK : in std_logic;
LEDS : out std_logic_vector(7 downto 0) := "11111111";
RST : in std_logic := '0');
end DataCntrl;
architecture Behavioral of DataCntrl is
-------------------------------------------------------------------------
-- Local Component, Type, and Signal declarations.
-------------------------------------------------------------------------
-------------------------------------------------------------------------
--
--Title: Component Declarations
--
--Description: This component is the UART that is to be tested.
-- The UART code can be found in the included
-- RS232RefComp.vhd file.
--
-------------------------------------------------------------------------
component RS232RefComp
Port ( TXD : out std_logic := '1';
RXD : in std_logic;
CLK : in std_logic;
DBIN : in std_logic_vector (7 downto 0);
DBOUT : out std_logic_vector (7 downto 0);
RDA : inout std_logic;
TBE : inout std_logic := '1';
RD : in std_logic;
WR : in std_logic;
PE : out std_logic;
FE : out std_logic;
OE : out std_logic;
RST : in std_logic := '0');
end component;
-------------------------------------------------------------------------
--
--Title: Type Declarations
--
--Description: There is one state machine used in this program, called
-- the mainState state machine. This state machine controls
-- the flow of data around the UART; allowing for data to be
-- changed from serial to parallel, and then back to serial.
--
-------------------------------------------------------------------------
type mainState is (
stReceive,
stSend);
-------------------------------------------------------------------------
--
--Title: Local Signal Declarations
--
--Description: The signals used by this entity are described below:
--
-- -dbInSig : This signal is the parallel data input
-- for the UART
-- -dbOutSig : This signal is the parallel data output
-- for the UART
-- -rdaSig : This signal will get the RDA signal from
-- the UART
-- -tbeSig : This signal will get the TBE signal from
-- the UART
-- -rdSig : This signal is the RD signal for the UART
-- -wrSig : This signal is the WR signal for the UART
-- -peSig : This signal will get the PE signal from
-- the UART
-- -feSig : This signal will get the FE signal from
-- the UART
-- -oeSig : This signal will get the OE signal from
-- the UART
--
-- The following signals are used by the main state machine
-- for state control:
--
-- -stCur, stNext
--
-------------------------------------------------------------------------
signal dbInSig : std_logic_vector(7 downto 0);
signal dbOutSig : std_logic_vector(7 downto 0);
signal rdaSig : std_logic;
signal tbeSig : std_logic;
signal rdSig : std_logic;
signal wrSig : std_logic;
signal peSig : std_logic;
signal feSig : std_logic;
signal oeSig : std_logic;
signal stCur : mainState := stReceive;
signal stNext : mainState;
------------------------------------------------------------------------
-- Module Implementation
------------------------------------------------------------------------
begin
------------------------------------------------------------------------
--
--Title: LED definitions
--
--Description: This series of definitions allows the scan code to be
-- displayed on the LEDs on the FPGA system board. Because the
-- dbOutSig is the scan code backwards, the LEDs must be
-- defined backwards from the dbOutSig.
--
------------------------------------------------------------------------
LEDS(7) <= dbOutSig(0);
LEDS(6) <= dbOutSig(1);
LEDS(5) <= dbOutSig(2);
LEDS(4) <= dbOutSig(3);
LEDS(3) <= dbOutSig(4);
LEDS(2) <= dbOutSig(5);
LEDS(1) <= dbOutSig(6);
LEDS(0) <= dbOutSig(7);
-------------------------------------------------------------------------
--
--Title: RS232RefComp map
--
--Description: This maps the signals and ports in main to the
-- RS232RefComp. The TXD, RXD, CLK, and RST of main are
-- directly tied to the TXD, RXD, CLK, and RST of the
-- RS232RefComp. The remaining RS232RefComp ports are
-- mapped to internal signals in main.
--
-------------------------------------------------------------------------
UART: RS232RefComp port map ( TXD => TXD,
RXD => RXD,
CLK => CLK,
DBIN => dbInSig,
DBOUT => dbOutSig,
RDA => rdaSig,
TBE => tbeSig,
RD => rdSig,
WR => wrSig,
PE => peSig,
FE => feSig,
OE => oeSig,
RST => RST);
-------------------------------------------------------------------------
--
--Title: Main State Machine controller
--
--Description: This process takes care of the Main state machine
-- movement. It causes the next state to be evaluated on
-- each rising edge of CLK. If the RST signal is strobed,
-- the state is changed to the default starting state, which
-- is stReceive.
--
-------------------------------------------------------------------------
process (CLK, RST)
begin
if (CLK = '1' and CLK'Event) then
if RST = '1' then
stCur <= stReceive;
else
stCur <= stNext;
end if;
end if;
end process;
-------------------------------------------------------------------------
--
--Title: Main State Machine
--
--Description: This process defines the next state logic for the Main
-- state machine. The main state machine controls the data
-- flow for this testing program in order to send and
-- receive data.
--
-------------------------------------------------------------------------
process (stCur, rdaSig, dboutsig)
begin
case stCur is
-------------------------------------------------------------------------
--
--Title: stReceive state
--
--Description: This state waits for the UART to receive data. While in
-- this state, the rdSig and wrSig are held low to keep the
-- UART from transmitting any data. Once the rdaSig is set
-- high, data has been received, and is safe to transmit. At
-- this time, the stSend state is loaded, and the dbOutSig
-- is copied to the dbInSig in order to transmit the newly
-- acquired parallel information.
--
-------------------------------------------------------------------------
when stReceive =>
rdSig <= '0';
wrSig <= '0';
if rdaSig = '1' then
dbInSig <= dbOutSig;
stNext <= stSend;
else
stNext <= stReceive;
end if;
-------------------------------------------------------------------------
--
--Title: stSend state
--
--Description: This state tells the UART to send the parallel
-- information found in dbInSig. It does this by strobing
-- both the rdSig and wrSig signals high. Once these
-- signals have been strobed high, the stReceive state is
-- loaded.
--
-------------------------------------------------------------------------
when stSend =>
rdSig <= '1';
wrSig <= '1';
stNext <= stReceive;
end case;
end process;
end Behavioral;
在上面的代码的基础上，我试图创建自己的状态机，允许我从一个终端接收到缓冲区的几个字节，更改状态并将此字节从缓冲区发送到终端我的电脑。 我从制作计数器开始计算接收字节的数量。我最终不知道发生了什么，因为计数器不是一个地改变它的值而是随机地改变它的值。我是VHDL的新手，我们将不胜感激。
library IEEE;
use IEEE.STD_LOGIC_1164.ALL;
use IEEE.STD_LOGIC_ARITH.ALL;
use IEEE.STD_LOGIC_UNSIGNED.ALL;
use IEEE.NUMERIC_STD.ALL;
entity DataCntrl is
Port ( TXD : out std_logic := '1';
RXD : in std_logic := '1';
CLK : in std_logic;
LED : out std_logic_vector(7 downto 0) := "00000000";
RST : in std_logic := '0');
end DataCntrl;
architecture Behavioral of DataCntrl is
component RS232RefComp
Port ( TXD : out std_logic := '1';
RXD : in std_logic;
CLK : in std_logic;
DBIN : in std_logic_vector (7 downto 0);
DBOUT : out std_logic_vector (7 downto 0);
RDA : inout std_logic;
TBE : inout std_logic := '1';
RD : in std_logic;
WR : in std_logic;
PE : out std_logic;
FE : out std_logic;
OE : out std_logic;
RST : in std_logic := '0');
end component;
type mainState is (
stReceive, stA,
stRereceive);
signal dbInSig : std_logic_vector(7 downto 0);
signal dbOutSig : std_logic_vector(7 downto 0);
signal rdaSig : std_logic;
signal tbeSig : std_logic;
signal rdSig : std_logic;
signal wrSig : std_logic;
signal peSig : std_logic;
signal feSig : std_logic;
signal oeSig : std_logic;
signal stCur : mainState := stReceive;
signal stNext : mainState;
begin
UART: RS232RefComp port map ( TXD => TXD,
RXD => RXD,
CLK => CLK,
DBIN => dbInSig,
DBOUT => dbOutSig,
RDA => rdaSig,
TBE => tbeSig,
RD => rdSig,
WR => wrSig,
PE => peSig,
FE => feSig,
OE => oeSig,
RST => RST);
process (CLK, RST)
begin
if (CLK = '1' and CLK'Event) then
if RST = '1' then
stCur <= stReceive;
else
stCur <= stNext;
end if;
end if;
end process;
process (stCur, rdaSig, dboutsig)
variable Send: std_logic :='0';
variable Count: integer :=0;
variable Jol: integer :=0;
begin
Jol:=Count;
Led<=std_logic_vector(to_unsigned(Jol,8));
case stCur is
when stReceive =>
rdSig <= '0';
wrSig <= '0';
if rdaSig = '1' then
Send:='0';
dbInSig <= dbOutSig;
if(Count=4) then
dbInSig <= "11101111";
stNext <= stA;
else
stNext <= stRereceive;
end if;
else
stNext <= stReceive;
end if;
when stRereceive =>
rdSig <= '1';
if(Send='0') then
Count:=Count+1;
Send:='1';
end if;
stNext <= stReceive;
when stA=>
wrSig <= '1';
rdSig <= '1';
end case;
end process;
end Behavioral;
答案 0 :(得分：0)
所以，看看你的计数器增量代码：
process (stCur, rdaSig, dboutsig)
[...]
variable Count: integer := 0;
begin
[...]
case stCur is
[...]
when stRereceive =>
[...]
if(Send='0') then
Count:=Count+1;
让我们分析一下我们在这里看到的内容。
count是一个变量。count在组合过程中增加。[让我们忘记你的敏感度列表不完整]
当你说'＃34;计数器改变它的值不是一个＆＃34;时，我假设你希望它在每个时钟周期增加1（或可比）。但是为了能够增加之前的值，计数器必须保持之前的值。这意味着需要注册。但是，寄存器需要时钟输入。因此，在无时钟的组合过程中没有推断出寄存器。
然后：不要将变量用于注册值。只有极少数情况下你应该使用变量，而这不是其中之一。
这是时钟计数器进程的一个例子
architecture rtl of ent is
signal count : unsigned(3 downto 0) := (others => '0');
begin
clk_proc : process (clk)
begin
if rising_edge(clk) then
if [condition] then
count <= count + 1;
end if;
if reset = '1' then
count <= (others => '0');
end if;
end if;
end process;