亲爱的所有最伟大的领主，
有些专家列出了连接无线网络的详细信息，
This is a step-to-step guide for connecting to a WPA/WPA2 WiFi network via the Linux command line interface. The tools are:
wpa_supplicant
iw
ip
ping
iw is the basic tool for WiFi network-related tasks, such as finding the WiFi device name, and scanning access points. wpa_supplicant is the wireless tool for connecting to a WPA/WPA2 network. ip is used for enabling/disabling devices, and finding out general network interface information.
The steps for connecting to a WPA/WPA2 network are:
Find out the wireless device name.
$ /sbin/iw dev
phy#0
Interface wlan0
ifindex 3
type managed
The above output showed that the system has 1 physical WiFi card, designated as phy#0. The device name is wlan0. The type specifies the operation mode of the wireless device. managed means the device is a WiFi station or client that connects to an access point.
Check that the wireless device is up.
$ ip link show wlan0
3: wlan0: (BROADCAST,MULTICAST) mtu 1500 qdisc noop state DOWN mode DEFAULT qlen 1000
link/ether 74:e5:43:a1:ce:65 brd ff:ff:ff:ff:ff:ff
Look for the word "UP" inside the brackets in the first line of the output.
In the above example, wlan0 is not UP. Execute the following command to bring it up:
$ sudo ip link set wlan0 up
[sudo] password for peter:
Note: you need root privilege for the above operation.
If you run the show link command again, you can tell that wlan0 is now UP.
$ ip link show wlan0
3: wlan0: (NO-CARRIER,BROADCAST,MULTICAST,UP) mtu 1500 qdisc mq state DOWN mode DEFAULT qlen 1000
link/ether 74:e5:43:a1:ce:65 brd ff:ff:ff:ff:ff:ff
Check the connection status.
$ /sbin/iw wlan0 link
Not connected.
The above output shows that you are not connected to any network.
Scan to find out what WiFi network(s) are detected
$ sudo /sbin/iw wlan0 scan
BSS 00:14:d1:9c:1f:c8 (on wlan0)
... sniped ...
freq: 2412
SSID: stanford
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: (0x0000)
... sniped ...
The 2 important pieces of information from the above are the SSID and the security protocol (WPA/WPA2 vs WEP). The SSID from the above example is stanford. The security protocol is RSN, also commonly referred to as WPA2. The security protocol is important because it determines what tool you use to connect to the network.
Connect to WPA/WPA2 WiFi network.
This is a 2 step process. First, you generate a configuration file for wpa_supplicant that contains the pre-shared key ("passphrase") for the WiFi network.
$ sudo -s
[sudo] password for peter:
$ wpa_passphrase stanford >> /etc/wpa_supplicant.conf
...type in the passphrase and hit enter...
wpa_passphrase takes the SSID as the single argument. You must type in the passphrase for the WiFi network stanford after you run the command. Using that information, wpa_passphrase will output the necessary configuration statements to the standard output. Those statements are appended to the wpa_supplicant configuration file located at /etc/wpa_supplicant.conf.
Note: you need root privilege to write to /etc/wpa_supplicant.conf.
$ cat /etc/wpa_supplicant.conf
# reading passphrase from stdin
network={
ssid="stanford"
#psk="testtest"
psk=4dfe1c985520d26a13e932bf0acb1d4580461dd854ed79ad1a88ec221a802061
}
The second step is to run wpa_supplicant with the new configuration file.
$ sudo wpa_supplicant -B -D wext -i wlan0 -c /etc/wpa_supplicant.conf
-B means run wpa_supplicant in the background.
-D specifies the wireless driver. wext is the generic driver.
-c specifies the path for the configuration file.
Use the iw command to verify that you are indeed connected to the SSID.
$ /sbin/iw wlan0 link
Connected to 00:14:d1:9c:1f:c8 (on wlan0)
SSID: stanford
freq: 2412
RX: 63825 bytes (471 packets)
TX: 1344 bytes (12 packets)
signal: -27 dBm
tx bitrate: 6.5 MBit/s MCS 0
bss flags: short-slot-time
dtim period: 0
beacon int: 100
Obtain IP address by DHCP
$ sudo dhclient wlan0
Use the ip command to verify the IP address assigned by DHCP. The IP address is 192.168.1.113 from below.
$ ip addr show wlan0
3: wlan0: mtu 1500 qdisc mq state UP qlen 1000
link/ether 74:e5:43:a1:ce:65 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.113/24 brd 192.168.1.255 scope global wlan0
inet6 fe80::76e5:43ff:fea1:ce65/64 scope link
valid_lft forever preferred_lft forever
Add default routing rule.
The last configuration step is to make sure that you have the proper routing rules.
$ ip route show
192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.113
The above routing table contains only 1 rule which redirects all traffic destined for the local subnet (192.168.1.x) to the wlan0 interface. You may want to add a default routing rule to pass all other traffic through wlan0 as well.
$ sudo ip route add default via 192.168.1.254 dev wlan0
$ ip route show
default via 192.168.1.254 dev wlan0
192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.113
ping external ip address to test connectivity
$ ping 8.8.8.8
PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
64 bytes from 8.8.8.8: icmp_req=1 ttl=48 time=135 ms
64 bytes from 8.8.8.8: icmp_req=2 ttl=48 time=135 ms
64 bytes from 8.8.8.8: icmp_req=3 ttl=48 time=134 ms
^C
--- 8.8.8.8 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2000ms
rtt min/avg/max/mdev = 134.575/134.972/135.241/0.414 ms
The above series of steps is a very verbose explanation of how to connect a WPA/WPA2 WiFi network. Some steps can be skipped as you connect to the same access point for a second time. For instance, you already know the WiFi device name, and the configuration file is already set up for the network. The process needs to be tailored according to your situation.
完全按照上面的教程，我无法连接无线路由器。
（以root身份工作）
......
#wpa_supplicant -B -i wlan0 -c /etc/wpa_supplicant.conf -D wext
#iw wlan0 link
Not connected.
即使我使用
禁用WPA身份验证iwconfig wlan0 essid XXXXXXXXXXXXX
无济于事。
但是GNOME无线托盘正在运行（可以选择，连接，断开连接等）
提前多多谢谢你。
答案 0 :(得分：0)
最新的wpa_supplicant能够完成所有工作 您写的wpa_supplicant选项对我来说似乎没问题 但请检查文件＆＃34; /etc/wpa_supplicant.conf"中的选项，如果它可读并写得很好（ssid，wpa，密码正确....）