Question

STM32应用笔记2606对此进行了讨论，但没有简单的代码示例。

Answer 1

此答案已在使用IAR EWARM的STM32F072 Nucleo板上进行了测试。这个答案使用＆＃34; STM32标准外设库＆＃34;没有别的。

请注意，验证您是否成功处于引导加载程序模式（DFU模式）的最佳/最简单方法是在线路PA_9上连接USB-2-UART转换器（从Sparkfun获取一个：http://sfe.io/p9873，价格为15美元）（USART1_TX）和PA_10（USART1_RX）（也不要忘记连接地面）。我无法使用Nucleo USART2默认连接（/ dev / ttyACM0），因此无法使用外部USB-2-USART连接。然后创建一个简单的C程序，在USART连接上写入0x7F。如果您处于DFU模式，它将回复一个字节：0x79。我使用Ubuntu，所以我的测试程序在Linux上编译并运行。

此外，测试引导加载程序模式（也称为DFU模式）的最简单方法是将BOOT0线跳转到+ 3.3V。这些在Nucleo上彼此相邻。

添加到main.c main（）例程：

// Our STM32 F072 has:
// 16k SRAM in address 0x2000 0000 - 0x2000 3FFF
*((unsigned long *)0x20003FF0) = 0xDEADBEEF;

// Reset the processor
NVIC_SystemReset();

在SystemInit（）函数的开头向Libraries / sysconfig / system_stm32f0xx.c添加一些代码：

// Define our function pointer
void (*SysMemBootJump)(void);

void SystemInit (void)
{
  // Check if we should go into bootloader mode.
  //
  // Set the main stack pointer __set_MSP() to its default value.  The default
  // value of the main stack pointer is found by looking at the default value
  // in the System Memory start address. Do this in IAR View -> Memory.  I
  // tried this and it showed address: 0x200014A8 which I then tried here.
  // The IAR compiler complained that it was out of range.  After some
  // research, I found the following from "The STM32 Cortex-M0 Programming
  // Manual":
  //         Main Stack Pointer (MSP)(reset value). On reset, the processor
  //         loads the MSP with the value from address 0x00000000.
  //
  // So I then looked at the default value at address 0x0 and it was 0x20002250
  //
  // Note that 0x1fffC800 is "System Memory" start address for STM32 F0xx
  //
  if ( *((unsigned long *)0x20003FF0) == 0xDEADBEEF ) {
       *((unsigned long *)0x20003FF0) =  0xCAFEFEED; // Reset our trigger
      __set_MSP(0x20002250);
                                                     // 0x1fffC800 is "System Memory" start address for STM32 F0xx
      SysMemBootJump = (void (*)(void)) (*((uint32_t *) 0x1fffC804)); // Point the PC to the System Memory reset vector (+4)
      SysMemBootJump();
      while (1);
  }

  ... // The rest of the vanilla SystemInit() function

创建一个简单的实用程序，以查看您是否处于引导加载程序模式（也称为DFU模式）。这在Linux上编译并运行。确保你的串口正确。它可能是/ dev / ttyUSB0，如下所示。

//
// A bare-bones utility: Test if the STM32 is in DFU mode
// (aka bootloader mode, aka firmware update mode).
//
// If it is in DFU mode, you can send it 0x7F over a UART port and it
// will send 0x79 back.
//
// For details, see the STM32 DFU USART spec.
//

#include <termios.h>
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <fcntl.h>
#include <signal.h>
#include <sys/types.h>
#include <sys/wait.h>
#include <string.h>
#include <errno.h>  // errno

#define DEFAULT_SERDEVICE  "/dev/ttyUSB0"
//#define DEFAULT_SERDEVICE  "/dev/ttyACM0"

int main(int argc, char **argv)
{
    int              fd, cooked_baud = B9600;
    char            *sername = DEFAULT_SERDEVICE;
    struct termios   oldsertio, newsertio;
    unsigned char mydata[2] = {0};

    mydata[0] = 0x7F;
    mydata[1] = 0;

    /* Not a controlling tty: CTRL-C shouldn't kill us. */
    fd = open(sername, O_RDWR | O_NOCTTY);
    if ( fd < 0 )
    {
        perror(sername);
        exit(-1);
    }

    tcgetattr(fd, &oldsertio); /* save current modem settings */

    /*
     * 8 data, EVEN PARITY, 1 stop bit. Ignore modem control lines. Enable
     * receive. Set appropriate baud rate. NO HARDWARE FLOW CONTROL!
     */
    newsertio.c_cflag = cooked_baud | CS8 | CLOCAL | CREAD | PARENB;

    /* Raw input. Ignore errors and breaks. */
    newsertio.c_iflag = IGNBRK | IGNPAR;

    /* Raw output. */
    newsertio.c_oflag = OPOST;

    /* No echo and no signals. */
    newsertio.c_lflag = 0;

    /* blocking read until 1 char arrives */
    newsertio.c_cc[VMIN]=1;
    newsertio.c_cc[VTIME]=0;

    /* now clean the modem line and activate the settings for modem */
    tcflush(fd, TCIFLUSH);
    tcsetattr(fd,TCSANOW,&newsertio);

    // Here is where the magic happens
    write(fd,&mydata[0],1);
    int red = read(fd,&mydata[1],1);
    if (red < 0) {
        fprintf(stderr, "Error: read() failed, errno [%d], strerrer [%s]\n",
                errno, strerror(errno));
    }

    tcsetattr(fd,TCSANOW,&oldsertio);
    close(fd);

    printf("Read [%d] bytes: [0x%x]\n", red, mydata[1]);

    return 0;
}

Answer 2

在我的项目中，我基本上和Brad一样，但没有修改SystemInit（）函数。

CubeMX HAL定义为

void __attribute__((weak)) __initialize_hardware_early(void);

在我的情况下 - 只是调用SystemInit（）;

所以你可以覆盖这个功能：

#include <stdint.h>
#include "stm32f0xx_hal.h"

#define SYSMEM_RESET_VECTOR            0x1fffC804
#define RESET_TO_BOOTLOADER_MAGIC_CODE 0xDEADBEEF
#define BOOTLOADER_STACK_POINTER       0x20002250

uint32_t dfu_reset_to_bootloader_magic;

void __initialize_hardware_early(void)
{
    if (dfu_reset_to_bootloader_magic == RESET_TO_BOOTLOADER_MAGIC_CODE) {
        void (*bootloader)(void) = (void (*)(void)) (*((uint32_t *) SYSMEM_RESET_VECTOR));
        dfu_reset_to_bootloader_magic = 0;
        __set_MSP(BOOTLOADER_STACK_POINTER);
        bootloader();
        while (42);
    } else {
        SystemInit();
    }
}

void dfu_run_bootloader()
{
    dfu_reset_to_bootloader_magic = RESET_TO_BOOTLOADER_MAGIC_CODE;
    NVIC_SystemReset();
}

如何在STM32 F072的软件中跳转到引导加载程序（DFU模式）？

2 个答案: