Question

我买了这个传感器：

http://dlnmh9ip6v2uc.cloudfront.net/datasheets/Sensors/Weather/RHT03.pdf

输出为“MaxDetect 1-wire bus”，它是什么意思以及如何使用它？我试图将它连接到arduino并对其进行编程，但它无法正常工作，我不断收到1位数据。我猜我的代码错了。我是否需要将Wire-1库用于arduino？

int SensorVccPin = 8; 
int datapin = 6;
int bitcheck1;
int bitcheck2;
int temp[16];
int humidity[16];
int sensorcheck[8];

void setup()
{
  pinMode(SensorVccPin, OUTPUT);  
    pinMode(datapin, INPUT);
    Serial.begin(9600); 
}

void loop()
{
    // This is the STEP #1
    digitalWrite(SensorVccPin, HIGH);  
  delay(5000); 

    digitalWrite(SensorVccPin, LOW);
     delay(15);


  digitalWrite(SensorVccPin, HIGH);  

  delayMicroseconds(30);   

  digitalWrite(SensorVccPin, LOW);  



while(digitalRead(datapin) == 0){

      delayMicroseconds(2);   }



   while(digitalRead(datapin) == HIGH)
{
delayMicroseconds(2);   }




  // STEP #2
  for (int i = 0; i<16; i++)
  {
    while(digitalRead(datapin) == LOW)
    {
      delayMicroseconds(2); }  

    delayMicroseconds(10);


  bitcheck1 = digitalRead(datapin);   // maybe store as an array
     delayMicroseconds(17);      // 50 sec pause  // 27us = 0 bit, 70us is 1 bit data
  delayMicroseconds(15); 
  bitcheck2 = digitalRead(datapin);

  if (bitcheck1==bitcheck2)
  {temp[i]=1;
  delayMicroseconds(28); 
  }
  else
  {temp[i]=0;

  }


    }

    for (int i = 0; i<16; i++)
  {
    while(digitalRead(datapin) == LOW)
    {
      delayMicroseconds(2); }  

    delayMicroseconds(10);


  bitcheck1 = digitalRead(datapin);   // maybe store as an array
     delayMicroseconds(17);      // 50 sec pause  // 27us = 0 bit, 70us is 1 bit data
  delayMicroseconds(15); 
  bitcheck2 = digitalRead(datapin);

  if (bitcheck1==bitcheck2)
  {humidity[i]=1;
  delayMicroseconds(28); 
  }
  else
  {humidity[i]=0;

  }


    }


    for (int i = 0; i<8; i++)
  {
    while(digitalRead(datapin) == LOW)
    {
      delayMicroseconds(2); }  

    delayMicroseconds(10);


  bitcheck1 = digitalRead(datapin);   // maybe store as an array
     delayMicroseconds(17);      // 50 sec pause  // 27us = 0 bit, 70us is 1 bit data
  delayMicroseconds(15); 
  bitcheck2 = digitalRead(datapin);

  if (bitcheck1==bitcheck2)
  {sensorcheck[i]=1;
  delayMicroseconds(28); 
  }
  else
  {sensorcheck[i]=0;

  }



  delayMicroseconds(80); 





  for(int i=0; i<16; i++)
  {
   Serial.print(temp[i]); 

  }
     Serial.print("  temp  "); 


  for(int i=0; i<16; i++)
  {
   Serial.print(humidity[i]); 

  }
       Serial.print("  hum  "); 

  for(int i=0; i<8; i++)
  {
   Serial.print(sensorcheck[i]); 

  }
       Serial.print(" check   "); 


    }



  }

Answer 1

应始终将VCC引脚（引脚1）保持为高电平。事实上，理想情况下，它应该连接到电源。这是数据引脚（引脚2），你应该拉高和低与传感器通信，它是你应该读取的数据引脚。您必须在输入和输出模式之间切换数据引脚。确保数据引脚上有一个上拉电阻，因为传感器只能将其拉低。

Answer 2

MaxDetect 1线总线由MaxDetect Technology Co.，Ltd。专门设计，与Maxim / Dallas 1线总线不同，因此与Dallas 1线总线不兼容。

你可以看一下：

http://tienda.tdrobotica.co/download/RHT03_programa.pdf

最好的问候。

什么是MaxDetect 1线总线？

2 个答案: