Question

我想在初始化TIM1的PWM时我做错了什么。我需要在PA8上获得一个信号，但我的代码（适用于TIM2-TIM5）对TIM1不起作用。以下任何设置都有误吗？

首先我认为这是因为我没有调用TIM_OCStructInit（），但是在添加之后我仍然在PA8上得到一个低级别而没有信号。它配置为AF_PP，我没有重新映射TIM1 ..

... {.tim = TIM1, .id = RCC_APB2Periph_TIM1, 
    .channels = {
        {.gpio = GPIOA, .gpio_pin = GPIO_Pin_8, },
        {.gpio = GPIOA, .gpio_pin = GPIO_Pin_9, },
        {.gpio = GPIOA, .gpio_pin = GPIO_Pin_10, },
        {.gpio = GPIOA, .gpio_pin = GPIO_Pin_11, }
    }
} ... 

.....

RCC_APB1PeriphClockCmd(_timers[tim_id].id, ENABLE);

TIM_TimeBaseInitTypeDef timerInitStructure;
TIM_OCInitTypeDef outputChannelInit;

TIM_TimeBaseStructInit(&timerInitStructure); 

timerInitStructure.TIM_Prescaler = F_CPU/1000000UL; // set 1us resolution
timerInitStructure.TIM_CounterMode = TIM_CounterMode_Up;
timerInitStructure.TIM_Period = period;
timerInitStructure.TIM_ClockDivision = TIM_CKD_DIV1;
timerInitStructure.TIM_RepetitionCounter = 0;
TIM_TimeBaseInit(TIMx, &timerInitStructure);

TIM_OCStructInit(&outputChannelInit); 

outputChannelInit.TIM_OCMode = TIM_OCMode_PWM1;
outputChannelInit.TIM_Pulse = def_width;
outputChannelInit.TIM_OutputState = TIM_OutputState_Enable;
outputChannelInit.TIM_OCPolarity = TIM_OCPolarity_High;


switch((chan & 0x3)){
    case 0: 
        TIM_OC1Init(TIMx, &outputChannelInit);
        TIM_OC1PreloadConfig(TIMx, TIM_OCPreload_Enable);
        break; 
    case 1: 
        TIM_OC2Init(TIMx, &outputChannelInit);
        TIM_OC2PreloadConfig(TIMx, TIM_OCPreload_Enable);
        break; 
    case 2: 
        TIM_OC3Init(TIMx, &outputChannelInit);
        TIM_OC3PreloadConfig(TIMx, TIM_OCPreload_Enable);
        break; 
    case 3: 
        TIM_OC4Init(TIMx, &outputChannelInit);
        TIM_OC4PreloadConfig(TIMx, TIM_OCPreload_Enable);
        break; 
}; 

//TIM_ARRPreloadConfig(TIMx, ENABLE);
TIM_CtrlPWMOutputs(TIMx, ENABLE);
TIM_Cmd(TIMx, ENABLE);

GPIO_InitTypeDef gpioStructure;
gpioStructure.GPIO_Pin = _timers[tim_id].channels[chan & 0x3].gpio_pin;
gpioStructure.GPIO_Mode = GPIO_Mode_AF_PP;
gpioStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(_timers[tim_id].channels[chan & 0x3].gpio, &gpioStructure);

Answer 1

知道了！当我应该为TIM1使用RCC_APB2PeriphClockCmd时，我正在为所有计时器使用RCC_APB1PeriphClockCmd。现在一切都很棒！

STM32F103 TIM1 pwm输出

1 个答案: