ModelSim - 无法模拟按钮按下

Question

我想使用四个按钮作为输入，三个七段LED显示器作为输出。两个按钮应在16个RAM位置上下移动;另外两个应该递增和递减当前显示的内存位置的内容。我有以下两个实体：

library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;

entity DE2_TOP is

  port (
    KEY : in std_logic_vector(3 downto 0);         -- Push button
    CLOCK_50: in std_logic;
    );

end DE2_TOP;

architecture datapath of DE2_TOP is

begin  
  U1: entity work.lab1 port map (
    key => key,
    clock => clock_50,        
  );

end datapath;

library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;

entity raminfr is                     -STANDARD RAM INFERENCE
    port (
        clock: in std_logic;
        we : in std_logic;
        a : in unsigned(3 downto 0);
        di : in unsigned(7 downto 0);
        do : out unsigned(7 downto 0)
    );
end raminfr;

architecture rtl of raminfr is

type ram_type is array (0 to 15) of unsigned(7 downto 0);
signal RAM : ram_type;
signal read_a : unsigned(3 downto 0);
begin
process (clock)
begin
    if rising_edge(clock) then
        if we = '1' then
            RAM(to_integer(a)) <= di;
        end if;
        read_a <= a;
    end if;
end process;
do <= RAM(to_integer(read_a));
end rtl;

和

library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;

entity lab1 is
    port(
        clock : in std_logic;
        key : in std_logic_vector(3 downto 0); 
        );
end lab1;

architecture up_and_down of lab1 is
    signal value_in_ram : unsigned(7 downto 0);
    signal we : std_logic;
    signal value_counter    : unsigned(7 downto 0) ;
    signal register_counter : unsigned(3 downto 0);
        begin
    U1: entity work.raminfr port map (
        a   => register_counter,
        di  => value_counter,
        do  => value_in_ram,
        clock => clock,
        we  => we
    );

    process(clock)
        begin
            if rising_edge(clock) then
                if (key(3)='0' and key(2)='0' and key(1)='1' and key(0)='0') then
                    value_counter <= value_counter + "1";   
                elsif (key(3)='0' and key(2)='0' and key(1)='0' and key(0)='1') then  
                    value_counter <= value_counter - "1";   
                elsif (key(3)='1' and key(2)='0' and key(1)='0' and key(0)='0') then
                    register_counter<= register_counter + "1";
                    value_counter <= value_in_ram;
                elsif (key(3)='0' and key(2)='1' and key(1)='0' and key(0)='0') then
                    register_counter<= register_counter - "1";
                    value_counter <= value_in_ram;
                end if;
            end if;
    end process;
end architecture up_and_down;

我还有以下测试台，我尝试通过KEY模拟按下按钮：

library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;


entity DE2_TOP_TEST is
end;

architecture BENCH of DE2_TOP_TEST is

    signal KEY :  std_logic_vector(3 downto 0);
    signal CLOCK_50 :  std_logic := '0';
    signal hex4, hex5, hex6 :  std_logic_vector(6 downto 0);           
begin
    clock_50 <= not clock_50 after 50 ns;
    process
        begin
            KEY<="0010";
                    wait for 1 us;
        KEY<="0000";
    end process;

uut:work.DE2_TOP port map (                                                         
    KEY=>key,
    CLOCK_50=>clock_50, 
    hex4=>hex4,
hex5=>hex5,
hex6=>hex6                                 
);
end BENCH;

我的测试台设置如下：

为了模拟，我编译了上述所有三个文件，然后模拟了DE2_TOP_TEST，但是我遇到的结果是我的“KEY”仍未定义，如下所示（尽管CLOCK_50确实获得了我设置的默认值）：

任何人都知道造成这种情况的原因是什么？

Answer 1

（1）您正在键入要测试的实体上有未连接的端口。测试结果与那些输入一样 - 特别是clk，未被驱动。

（2）连接clk后，您需要开车。

signal clk : std_logic := '0';

和

clk <= not clk after 50 ns;

应该给出一个10MHz的时钟，在模拟器中检查

（3）用特定的值序列驱动“KEY”

subtype keys is std_logic_vector(3 downto 0);
constant count_up : keys := "0001";
constant count_dn : keys := "0010";
constant idle     : keys := "0000"; 
-- etc

    process
    begin
        KEY <= count_up;
        wait for 1 us;
        KEY <= idle;
        wait for ...
-- etc
    end process;

（4）将OUTPUTS返回到测试平台，以便检查它们的值。如果要将它们连接到显示器，您需要将它们作为顶级（设计）实体中的端口引出！

然后（稍后，一旦事情开始计划），您可以在测试平台过程中测试它们......

    wait for 100 ns;
    -- after the last press, we should have "07" on the display
    assert digit(1) = "0111111" report "Left digit has wrong value" severity ERROR;
    assert digit(0) = "0000111" report "Left digit has wrong value" severity ERROR;

这样的自检测试台通过盯着波形来节省调试。只有在测试失败时才需要波形...